td62064,074p/ap/f/af 2003-02-26 1 toshiba bipolar digital integrated circuit silicon monolithic td62064p,td62064ap,td62064f,td62064af td62074p,td62074ap,td62074f,TD62074AF 4ch high ? current darlington sink driver the td62064p / ap / f / af and td62074p / ap / f / af are high ? voltage, high ? current darlington drivers comprised of four npn darlington pairs. all units feature integral clamp diodes for switching inductive loads and all units of td62074p / ap / f / af feature uncommitted collectors and emitters for isolated darlington applications. for proper operation, the substrate (sub) must be connected to the most negative voltage. applications include relay, hammer, lamp and stepping motor drivers. features output current (single output) 1 .5 a (max) high sustaining voltage output 35 v (min) (td62064p / f, 074p / f) 50 v (min) (td62064ap / af, 074ap / af) output clamp diodes : td62064p / ap / f / af isolated darlington array : td62074p / ap / f / af input compatible with ttl and 5 v cmos gnd and sub terminal = heat sink package type ? p, ap : dip ?1 6 pin package type ? f, af : hsop ?1 6 pin pin connection (top view) td62064p / ap td62074p / ap td62064f / af td62074f / af weight dip16 ? p ? 300 ? 2.54a : 1.11 g (typ.) hsop16 ? p ? 300 ? 1.00 : 0.50 g (typ.)
td62064,074p/ap/f/af 2003-02-26 2 schematics (each driver) td62064p / ap / f / af td62074p / ap / f / af note: the input and output parasitic diodes cannot be used as clamp diodes. precautions for using ( 1 ) this ic does not include built-in protection circuits for excess current or overvoltage. if this ic is subjected to excess current or overvoltage, it may be destroyed. hence, the utmost care must be taken when systems which incorporate this ic are designed. utmost care is necessary in the design of the output line, common and gnd line since ic may be destroyed due to short ? circuit between outputs, air contamination fault, or fault by improper grounding. (2) if a td62064p/ap/f/af is being used to drive an inductive load (such as a motor, solenoid or relay), toshiba recommends that the diodes (pins 1 and 8) be connected to the secondary power supply pin so as to absorb the counter electromotive force generated by the load. please adhere to the device?s maximum ratings. toshiba recommends that zener diodes be connected between the diodes (pins 1 and 8) and the secondary power supply pin (as the anode) so as to enable rapid absorption of the counter electromotive force. again, please adhere to the device?s maximum ratings. if a td62074p/ap/f/af is being used to drive an inductive load (such as a motor, solenoid or relay), toshiba recommends that a diode be connected between the output pin (as the anode) and the secondary power supply pin. please adhere to the device?s maximum ratings.
td62064,074p/ap/f/af 2003-02-26 3 maximum ratings (ta = 25c) characteristic symbol rating unit p, f ? 0.5~35 output sustaining voltage ap, af v ce (sus) ? 0.5~50 v output current i out 1.5 a / ch input current i in 50 ma input voltage v in ? 0.5~17 v p, f 35 clamp diode reverse voltage ap, af v r (note 1) 50 v clamp diode forward current i f (note 1) 1.5 a / ch p, f 35 isolated voltage ap, af v sub (note 2) 50 v p, ap 1.47 / 2.7 (note 3) power dissipation f, af p d 0.9 / 1.4 (note 4) w operating temperature t opr ? 40~85 c storage temperature t stg ? 55~150 c note 1: td62064p / ap / f / af note 2: td62074p / ap / f / af note 3: on glass epoxy pcb (50 50 1.6 mm cu 50%) note 4: on glass epoxy pcb (60 30 1.6 mm cu 30%) recommended operating conditions (ta = ? 40~85c) characteristic symbol test condition min typ. max unit p, f 0 D 35 output sustaining voltage ap, af v ce (sus) 0 D 50 v dc1 circuit, ta = 25c 0 D 1250 duty = 10 % 0 D 1250 p, ap (note 1) duty = 50 % 0 D 390 duty = 10 % 0 D 907 output current f, af (note 2) i out t pw = 25 ms 4 circuits t j = 120c ta = 85c duty = 50 % 0 D 172 ma / ch v in 0 D 8 v (output on) v in (on) i out = 1.25 a 2.5 D 8 v input voltage (output off) v in (off) 0 D 0.4 v input current i in 0 D 20 ma p, f 0 D 35 clamp diode reverse voltage ap, af v r td62064p / ap / f / af 0 D 50 v clamp diode forward current i f D D 1.25 a p, f D D 35 isolation voltage ap, af v sub td62074p / ap / f / af D D 50 v p, ap ta = 85c (note 1) D D 1.4 power dissipation f, af p d ta = 85c (note 2) D D 0.7 w note 1: on glass epoxy pcb (50 50 1.6 mm cu 50%) note 2: on glass epoxy pcb (60 30 1.6 mm cu 30%)
td62064,074p/ap/f/af 2003-02-26 4 electrical characteristics (ta = 25c) characteristic symbol test cir ? cuit test condition min typ. max unit v ce = 50 v, ta = 25c D D 50 ap, af v ce = 50 v, ta = 85c D D 500 v ce = 35 v, ta = 25c D D 50 output leakage current p, f i cex 1 v ce = 35 v, ta = 85c D D 500 a i out = 1.25 a, i in = 2 ma D D 1.6 collector ? emitter saturation voltage v ce (sat) 2 i out = 0.75 a, i in = 935 a D D 1.25 v i out = 1.0 a D 800 D dc current transfer ratio h fe 2 v ce = 2 v i out = 0.25 a D 1500 D input voltage (output on) v in (on) 3 i out = 1.25 a, i in = 2 ma D D 2.4 v v r = 50 v, ta = 25c D D 50 ap, af v r = 50 v, ta = 85c D D 100 v r = 35 v, ta = 25c D D 50 clamp diode leakage current f i r 4 v r = 35 v, ta = 85c D D 100 a clamp diode forward voltage v f 5 i f = 1.25 a D D 2 v input capacitance c in 6 v in = 0 v, f = 1mhz D 15 D pf p, f v out = 35 v, r l = 29 ? turn ? on delay ap, af t on v out = 50 v, r l = 42 ? D 0.1 D p, f v out = 35 v, r l = 29 ? turn ? off delay ap, af t off 7 c l = 15 pf v out = 50 v, r l = 42 ? D 1.0 D s
td62064,074p/ap/f/af 2003-02-26 5 test circuit 1 . i cex 2. v ce (sat) , h fe 3. v in (on) 4. i r 5. v f 6. c in 7. t on , t off note 1: pulse width 50 s, duty cycle 10% output impedance 50 ? , t r 5ns, t f 10ns note 2: c l includes probe and jig capacitance
td62064,074p/ap/f/af 2003-02-26 6
td62064,074p/ap/f/af 2003-02-26 7
td62064,074p/ap/f/af 2003-02-26 8 package dimensions dip16 ? p ? 300 ? 2.54a unit : mm weight: 1.11 g (typ.)
td62064,074p/ap/f/af 2003-02-26 9 package dimensions hsop16 ? p ? 300 ? 1.00 unit : mm weight: 0.50 g (typ.)
td62064,074p/ap/f/af 2003-02-26 10 toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc.. the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk. the products described in this document are subject to the foreign exchange and foreign trade laws. the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba corporation for any infringements of intellectual property or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any intellectual property or other rights of toshiba corporation or others. the information contained herein is subject to change without notice. 000707eb a restrictions on product use
|
